Description

Compatibility should be checked and confirmed before placing order! Steps of confirming the compatibilities: Manage " My Garage ", and chose the right one when placing order; Or chose the " Year / Make / Model / Trim / Engine " of your vehicle on the compatible chart; Or Contact us if you have any question in confirming the compatibility, to make sure you will get the right and compatible item. 1. The radiator cap that has not passed the test can’t release the pressure when it reaches the pressure value. 2. The damaged thermostat is unable to carry out a large cycle, resulting in a continuous increase in the radiator pressure. 3. The radiator fan does not turn, resulting in high temperature in the water tank. 4. Drain the air from the cooling system. Refer to the user manual or repair manual. 5. Please refer to owner's manual to add coolant. 6. Do not open the hood until the steam has subsided. The engine compartment may be very hot, causing serious injuries such as burns. 7. Please stop the vehicle immediately, when “ENGINE OVERHEAT/High Temperature” shows on the dashboard or steam comes out from under the hood. 8. Keep hands and clothing (especially a tie, a scarf) away from the fans and belts. Failure to do so may cause the hands or clothing to be caught, resulting in serious injuries. 9. Do not loosen the radiator cap while the engine and radiator are hot. Serious injuries, such as burns, may result from hot coolant and steam released under pressure. FEATURES: 1. The Core was made of high quality Aluminum . Effective Heat Dissipation. 2. Good sealing. All of the new radiators will be inspected before selling (Including 100% leaking test). 3. Radiator is really easy to get damaged during delivery. We have upgraded our package design to avoid this kind of problem. DETAILS: Core Material: Aluminum Tank Material: Plastic Core Dimension: 26-3/4 In. (H) x 15-11/16'' (W) In. Core Thickness: 1 In. (26mm) Inlet Diameter: 1-3/8 In. Outlet Diameter: 1-3/8 In. Row: 1 Transmission Oil Cooler: Included Interchange Part Number: CU13328, 13328, 20979496, RAD13328, GM3010551, GM3010553, Q13328, TYC13328 There are 2 types of installation method of the Fast connector: 1. Remove the original mount, insert the tube, and tighten the nut at the tip of tube. 2. The nut at the end of the tube is not needed, move it away from the tip. Next, insert the tube to the mount and push it to the bottom. The snap spring on the mount will keep the tube intact. Color: Black and Silver FITMENT: For 2014 - 2019 Chevrolet Impala 2.5L Only (Not for 3.6L) For 2013 - 2015 Chevrolet Malibu 2.0L & 2.5L Only (Not for 2.4L) For 2016 Chevrolet Malibu Limited 2.5L For 2015 - 2016 Buick Regal Base 2.0L Only (Not for 2.4L) For 2014 - 2016 Buick Regal Premium 2.0L Only (Not for 2.4L) For 2016 Buick Regal Sport Touring 2.0L Only (Not for 2.4L) How to clean radiator: 1. Start the vehicle, to rise to normal temperature. Slowly open the tank cover, the fluid shake from the tank after filling the mouth, the cleaner can be mixed with any brand of coolant. Idle running not less than 15 minutes, not cleaning vehicles not less than 30 minutes for two years. And then discharge coolant, flush water tank, until out of clear water, suitable for any water cycle system. 2. After cleaning, after waiting for pipeline rehabilitation add fluid to water tank, and inject new coolant and water purification. How to replace the radiator: 1. Disconnect the battery. 2. Drain the radiator fluid into a suitable container. 3. Remove the old radiator: -Take off any plastic covers around the radiator. -Disconnect the electrical connector to the fan, and unbolt and remove the fan assembly. -Disconnect the radiator hoses from the radiator. -Disconnect the transmission cooling lines from the bottom of the radiator. -Remove any clamps, brackets, or screws holding the radiator inside its frame. -Lift the radiator up and out of the car. 4. Install the new radiator: -Slide the new radiator into place. -Connect any clamps or brackets that hold the radiator in place. -Connect the transmission cooling lines carefully. -Connect the engine cooling hoses to the radiator. -Replace the fan and fan shroud. -Reconnect the fan electrical connection. -Replace the plastic covers. 5. Fill the radiator with fluid. 6. Check your work to make sure that there are no leaks. (Tools need to be prepared: Screwdrivers, Wrenches, Drain pan) Note: Do please keep children and pets away when replacing the radiator) Note: 1. Project operation, the vehicle normal temperature 60 to 80 degrees. 2. Add detergent if the tank is too full can take some antifreeze.